Sends a message when the button is pressed. Can recognize various types of button presses - quite simple with many use cases ranging from security to eldercare.
Guard me sends messages once the object moves, vibrates or changes position. After the alert is sent, the device is inert for the duration of the sleep time to prevent draining the battery.
Track me sends a message when the monitored object starts moving and also sends one when the movement stops and the device does not move for an adjustable time period.
Trace me sends messages while the object is moving and stops sending them when it’s still. While moving, it periodically sends a message (the period length is defined in the Tracing delay register) so you can trace the monitored object. No more messages are sent after stop of movement is detected and reported.
Using the accelerometer, this mode monitors occurrence of vibration and periodically reports when the monitored object was vibrating and when it was not in a predefined time window.
Reports movement of an object and once the movement stops, reports precise position through accelerometer data. You can use the data to determine whether the object was displaced or not.
Don’t drop me behaves similarly to Guard me except for its event (uplink message) is triggered by faster acceleration of the accelerometer in one of its axis and not just movement detection. Drop alert detection threshold can be defined.
Please note this mode should not be used on boards with an opto pin (SimpleIndustry with 2 external sensors) because of accelerometer consumption. Please contact us at ask.simplehw.eu for more information.
Sends a timeline of when and how long the reed contact was opened and when and how long it was closed, 8 time periods are sent in total. Useful for creating a history of e.g. door usage and more.
Detects doors opening and closing using the accelerometer and the magnetometer.
This mode lets you know when a water leak has occurred and also when water is no longer detected. Position is monitored and any tilt over a predefined threshold (up to 180 degrees) is reported. If the device returns to the original position, the device will send a message too.
Leak detector is only for the SimpleLeak! No other device works properly in this mode.
A mode created to literally show off. Will send some mode-specific events from Press me (0x01) and all mode-specific events from Don’t drop me (0x07), Reed on/off (0x0C) and Light on/off (0x0D) together with appended payload with voltage, temperature and accelerometer data. WiFi is used in one event.
Sends a message when the reed contact is switched on by a magnet and also sends one when the sensor is switched off because the nearby magnetic field is no longer detected.
Detects light - a message is sent every time a predefined threshold (% of light detected) is crossed either way. Can be set up to detect a very low light percentage threshold - darkness and extreme darkness (useful for monitoring package opening in the night).
Intended for long-term monitoring of temperature exception occurrences - in this mode, temperature exception is defined as temperature above or below the three predefined temperature thresholds A, B and C. Will send an event with 5 exceptions and the duration of each exception. Every exception with its duration will take up two bytes of the payload for a total of 12 bytes. The thresholds are encoded in SimpleTemp.
Intended for long-term monitoring of temperature exception occurrences - in this mode, temperature exception is defined as temperature above the predefined temperature delta. Will send an event with 5 exceptions and the duration of each exception. Every exception with its duration will take up two bytes of the payload for a total of 12 bytes (mode and event bytes included). The delta is encoded in SimpleTemp.
This mode sends an alert every time the measured temperature is above or below any of three predefined temperature thresholds A, B or C. The thresholds are encoded in SimpleTemp.
This mode sends an alert every time the measured temperature is above the predefined temperature delta. The delta is encoded in SimpleTemp.
Counts the number of reed contact switches and can report them in various ways. Very useful when you need to count e.g. rotation, door openings and closings etc.
Please note that the Legionella mode is only available in the SimpleIndustry Legionella device as it is not included in the standard API 6 build due to its size.
This mode was created to monitor water pipes and prevent growth of Legionella pneumophila bacteria that cause the legionnaire’s disease. A device with two external NTC sensors measures temperature of the pipe(s) in two modes and reports the temperature periodically.
The LED diode will start blinking when the button is pressed and will continue doing so until the button is pressed again. Used for simple LED indication.
Please note that the Gas monitoring mode is only available in the SimpleIndustry CH4 as it is not included in the standard API 6 build due to its size.
Monitors the concentration of gas regularly - reports 1) predefined gas threshold breaches (two thresholds available) and 2) periodic gas values (redundant data is configurable). Currently used for monitoring CH4.
Sends 2 MAC addresses regularly in a predefined period. Precise localisation with an emphasis on using as little battery life as possible as the MACs are sent in one message.
This mode doesn’t send any payload, only Sigfox metadata. The messages are sent periodically and the time period can be adjusted. Used for Sigfox localisation with the lowest battery consumption possible.